Matra présentera ses VAE au mondial du 2 roues

Forum dédié aux véhicules de ce constructeur Français: gamme VAE, Scooter e-Mo, quad GEM e2 et e4

Modérateurs : Remdo, man3515, moulino51

Répondre
Avatar du membre
Rémy
Messages : 9169
Enregistré le : jeu. 06 07 , 2006 14:48
Mes véhicules : Renault Fluence ZE - Nissan Leaf 2012
Localisation : FR-06-Antibes

Matra présentera ses VAE au mondial du 2 roues

Message par Rémy » lun. 24 09 , 2007 16:02

du 29 septembre au 7 octobre

Un peu plus d'informations ici.

Et un superbe modèle (proto ?) .

Bernhard Stroop
Messages : 195
Enregistré le : dim. 15 10 , 2006 10:30
Localisation : D-NW-GT-Rietberg / City-El 1991(2005),106 elec 1999(2007), VAE Matra i-Step 2007
Contact :

Message par Bernhard Stroop » lun. 24 09 , 2007 20:51

J'ai achetez aujourd'hui un I-Step city chez Accus-Service.
Super velo de vu mais à cause de la pluie je n'ai pas pu l'essayer :(
J'espère on va avoir encore de beau temps cette semaine pour que je puisse l'essayer dans une région vallonée.
Amicalement
Bernard
Citroen Berlingo electrique 1999

philelectrique
Messages : 77
Enregistré le : sam. 30 10 , 2004 14:57
Localisation : FR-56-Queven/matra i step

Message par philelectrique » mar. 02 10 , 2007 8:55

je l'ai vu au salon,tres beau look.peux tu nous donner tes premieres impressions?
phil

Bernhard Stroop
Messages : 195
Enregistré le : dim. 15 10 , 2006 10:30
Localisation : D-NW-GT-Rietberg / City-El 1991(2005),106 elec 1999(2007), VAE Matra i-Step 2007
Contact :

Message par Bernhard Stroop » mar. 02 10 , 2007 12:35

j'ai l'essayer dans une région avec beaucoup des boucles: Ribérac en Dordogne.
Même avec le moteur ca reste un vélo sportif. L'aide est proportionel à la force sur les pedals. Pour le gens qui ont l'habitude de forcer c'est bon, pour ceux qui aiment mouliner c'est un désadvantage. Peut-être il y a une possibilité de rentrer dans le menu pour regler ca. Pas encore trouvé.
Par contre pour l'Europe il y a une reglage, que l'aide de motor se diminue sa partir de 20 km/h et s'arête à partir de 25km/h.
C'est pas du tout agreable, quand on a l'habitude de rouler vite. Mais il existe un code pour arêter le limite ou pour le mettre sur limite americaine (20 mph).
Le système de l'aide (moteur, batterie et tableux) vient de Canada. Pour 1200 Euro on peut l'acheter et monter sur n'importe quel vélo mais a mon avis ca ne vaut pas le coup. Le cadre de Matra en 4 taille, aluminium, est bien fait. Je vais ajouté une tige de selle amortisé. Le velo pèse 20 kg plus les accus, (NiMh pour l'instant en Europe = 4 kg). Pour 750 Euro on peut acheter la version Lion en Canada ou suisse qui pèse que 2,8 kg.
On peut regler l'aide entre 1 - 4 (25, 50, 100 et 200%) mais 1 ou 2 suffit l'argement. La consommation avec 4 est important.
Pour les descentes (ou pour s'entrainer) on peut mettre entre 1 - 4 de recuperation. Ca recharge les batteries et évite de freiner. Si on fraine avec les leviers de freine, ca récupère aussi (avec 4). On dépense moin de coutchouk.
Le moteur, surtout en +4 ou -4, fait vibrer le velo et fait un peu de bruit, sinon c'est assez silencieux.
Pour l'autonomie je ne peux pas trop dire parce que ca dépend trop de relief ouon roule.
J'ai décidé de prendre la version City en taille L (j'ai 178cm) parce c'est équipé avec des lumières et une porte-bagage pour les saccoches.
Je veux l'utiliser pour aller les 16 km au travail en quand il fait beau, pour m'entrainer sans soufffrir et sans trop transpirer mais pour être assez vite. J'espère que je vais trouver encore le code pour diminuer la force sur pédale.
Amicalement
Bernard
Citroen Berlingo electrique 1999

filomat
Messages : 3452
Enregistré le : sam. 19 02 , 2005 12:45
Mes véhicules : e-trottinettes : 1 moonway gyroboarder i1 + 1 archos bolt
Localisation : FR-92-MEUDON

Message par filomat » mar. 02 10 , 2007 15:23

Save this on your computer if you want to keep it...


----------------------------------------------------------------


OLD BIONX SYSTEM CONSOLE CONFIGURATION GUIDE.


Table of Contents

1. DOCUMENT CONTENTS AND FIRMWARE REQUIREMENTS...............2
2. HOW TO ENTER A PARTICULAR CODE............................3
3. EPS1 – CONFIGURATION MENU (3771)..........................4
7. EPS2 – DIAGNOSTIC MODE (3772).............................6
8. EPS9 – REMAINING TIME & DISTANCE (3779)...................7
9. IMPORTANT NOTICE ABOUT SPEED LIMIT........................8
10. HOW TO CONTACT BIONX TEAM................................8

1. Document contents and firmware requirements

This document contains procedures and information that gives access to all
configurable parameters and hidden options of the BionX system. It is intended to the bike shop and BionX installation technicians.

This paper covers the console firmware revision #12 and higher. All the previous firmware revisions do not include all the functions mentioned in this document and/or the menu structure can be different.

If you own a system with older firmware, we recommend you to call EPS to get assistance as needed. However, it is also possible to upgrade the firmware on all BionX systems. (It is important to remember that the system performance is the same regardless of the firmware versions.)

2. How to enter a particular code

All following sections of this document use 4 digit codes. Whatever the user wants to access the configuration menu (3771), diagnostic screen (3772) or remaining variables (3779) the same method must be used:

1. Turn the system ON.

2. Hold down both ‘CHRONO’ and ‘MODE’ buttons at the same time until the
screen change to four zero (It takes about 2 seconds)

3. Using ‘A’ to increase the digit value and ‘G’ to decrease value, enter the first digit.

4. Push ‘MODE’ once to advance to the next digit.

5. Repeat step #3 and #4 for all remaining digits.
* If an invalid code is entered, the display will simply return to the normal display layout.

3. EPS1 – Configuration menu (3771)

The EPS1 menu gives access to the following parameters:

• Program the rear wheel circumference. (Millimetres)
• Select between imperial (mph) or metric (km/h) units.
• Configure the speed limit value and enabled/disabled status.
• Program the brake (regenerative) strength value.
• And finally view the console firmware version. (Nothing to configure here)

Here are the steps to navigate through EPS1 menu:

1. Enter the EPS1 code (3771) by following section #2 instructions.

2. If the 3771 code is correctly entered, you will see four digits that represent the actual wheel circumference in millimetres. If the user wants to keep the old circumference value, the same digits must overwrite the old ones. If a new wheel circumference has to be programmed, enter the new value. Use the following table to convert wheel diameters in inches to circumference in mm.

CONVERTION TABLE FOR THE EPS BionX WHEEL CIRCUMFERENCE PROGRAMMING (code # 3771)

Wheel diameter

Corresponding circumference (mm)

18'' = 1436 ; 20'' = 1596 22'' = 1756 24'' = 1915
26'' = 2075 27'' = 2156 700mm = 2199 28’’ = 2234

mm = 79.8 * Diameter

3. The next configuration screen is the unit configuration. Either ‘A’ or ‘G’ can be pushed to switch from imperial to metric:
• will select metric unit (kilometres)
• will configure the bike to imperial system (miles)

Push ‘MODE’ button when done to advance to the next configuration screen.

4. The third screen is used to configure the speed limit.

• Two parameters can be configured regarding the speed limit process:
Activation or not of the function and the limit level in km/h.
i. Pushing the chrono button will switch between the two
parameters.
ii. Use ‘A’ and ‘G’ to configure the speed threshold value or the
function state (0=no speed limit, 1=speed limit enabled)

Push ‘MODE’ button when done to advance to the next configuration screen.

5. The fourth menu is used to configure the braking generation level when the rear brake is applied. Use ‘A’ and ‘G’ to set the desired value. The configurable range is from 5 to 64. 64 will generate maximum breaking power while choosing a lower value will produce less regeneration breaking.

Push ‘MODE’ button when done to advance to the next configuration screen.

6. The final EPS1 screen shows the console firmware version. Nothing can be configured here. The image below shows firmware rev#12.

7. EPS2 – Diagnostic mode (3772)

Follow second section instructions to enter the EPS2 code. Screen will switch to a special ‘diagnostic’ mode where it is possible to monitor some important signals:

• Strain gage sensor value: (Cyclist effort sensor) when the cyclist push on the pedals, this signal will raise proportionally to the force applied.
• Battery voltage: Indicate the NIMH battery voltage in volt.
• Monitor the motor command: While the bike is operated, the assistance or generation level will appear on the two upper-left digits. Again, the values range if 0-64.

There is two ways to exit the special diagnostic display mode:

• Simply turn the system off. Next power ON will display normal layout.
• Re-enter the 3772 code will toggle display to normal layout.

8. EPS9 – Remaining time & Distance (3779)

BionX development team is always improving the product reliability and
performance. One of the latest add-in on the system firmware is the possibility to be informed about the remaining time and distance at any time, based on the last 10-20 seconds of bike utilisation history. This function being relatively new and presently under beta testing phase, is not available by default on a brand new system. However, BionX gives the possibility to access this feature for the users who wants to experience it.

Once again firmware revision #12 and more are a requirement to access the new variables. By entering a special unlock code, the users will have access to two more display variables:

• Remaining time:
As the user cycle to all different variables by pushing ‘chrono’ button, the prefix ‘Tr’ will appear. Tr stand for ‘Time Remaining’ (or Temps Restant in French). The unit is in hour with tenth of hour precision. The following example shows a remaining time of 4 hour 30 minutes.

• Remaining distance:
The variable name prefix is ‘dr’ (distance remaining, or distance
restante in french) and the value are in kilometres (or in miles if console
configured to imperial units). The following examples show a remaining
distance of 168 kilometres.

The procedure to unlock the feature is simply to enter the EPS9 code (3779) as mentioned into the second section of this document. The function becomes instantly accessible. Recycling the power is recommended after enabling the function. If the user wants to disable the function, it can be toggled ON and OFF by entering the same code again.

Since both variables require microcontroller processing time and multiples
operations, under certain conditions, one or both variable cannot be predicted. Per example, if the bike is stopped and the speed is null, remaining distance cannot be processed. Another case could be if the user use the regenerating brake for more than a few seconds, the remaining time would be infinite. In those particular cases, the value of either variable is replaced by three dash character (---). The picture below display an incalculable remaining distance:

9. Important notice about speed limit

Almost all BionX kits that have been released today are running firmware #12 and later. Regardless of the country, the laws are very strict regarding any electric bicycle speed limitation. Even if this guide give the user the possibility to configure or even remove the speed limit algorithm, EPS will not be responsible for any accidents or wounds that could results of an improper or non legal speed limit configuration.

All the bicycle kits sold from EPS are already configured to offer the maximum legal permissible speed for each corresponding countries. The limits are the following:

- America: 32 km/h or 20 mph
- Europe: 25 km/hr or 15.5 mph

All future firmware releases from EPS will avoid the user to play with the speed limit parameters.


--------------------------------------------------------------


NEW BIONX SYSTEM CONSOLE CONFIGURATION GUIDE

To enter the access section you push on MODE and CHRONO in same time.

2001: KM or Miles
2002: Generative Breaking
2003: Time last with the battery
2004: Clock
2005: Wheel size
2006: Programming brake sensor
2007: Polarity throttle (0-5volt or 5-0volt)

3771: wheel size
3772: diagnostic mode
3773: max speed
3775: throttle max speed
3776: Speed that motor will start
5000: Full reset
1976: motor direction
1234: sensor speed signal; 1= slow 5= fast
1970: Configuration activation backlight ad DCDC automatic
0007: Sensor signal gain, 0.1 to 4.0
0008: Configuration of extra assistance 1.0 to 4.0
0041: activation of the I2C

Error Code
SMC_ERROR_VCTRL 20
SMC_ERROR_VPRCH 21
SMC_ERROR_RELAY 22
SMC_ERROR_BMS 23
_________________
Que la force soit électrique !

filomat
Messages : 3452
Enregistré le : sam. 19 02 , 2005 12:45
Mes véhicules : e-trottinettes : 1 moonway gyroboarder i1 + 1 archos bolt
Localisation : FR-92-MEUDON

Message par filomat » mar. 02 10 , 2007 15:27

J'ai récupéré les informations précédentes sur ce forum :
http://endless-sphere.com/forums/viewforum.php?f=2
mais je n'ai pas réussi à retrouver le topic (everything you want to know about bion'x), donc j'ai fait un copié-collé
Que la force soit électrique !

philelectrique
Messages : 77
Enregistré le : sam. 30 10 , 2004 14:57
Localisation : FR-56-Queven/matra i step

Message par philelectrique » mer. 16 01 , 2008 20:47

slt,quels sont les boutons mode et chrono.j'ai 4 boutons:+,-,trip et start.
phil

filomat
Messages : 3452
Enregistré le : sam. 19 02 , 2005 12:45
Mes véhicules : e-trottinettes : 1 moonway gyroboarder i1 + 1 archos bolt
Localisation : FR-92-MEUDON

Message par filomat » jeu. 17 01 , 2008 15:43

Je ne sais pas (je n'ai pas de matra bion'x), à mon avis ce serait trip et start, trip pour mode et start pour chrono puisqu'ils parlent de A et G pour plus (add) et moins.
Je ne sais pas ce que l'on risque à appuyer simultanément sur trip et start pendant deux secondes pour voir si l'écran affiche quatre zéros.
Il serait plus prudent de se renseigner sur ceux (nombreux sur les forums) qui ont déjà fait la manip ou auprès d'un revendeur matra bion'x.
Que la force soit électrique !

philelectrique
Messages : 77
Enregistré le : sam. 30 10 , 2004 14:57
Localisation : FR-56-Queven/matra i step

Message par philelectrique » dim. 20 01 , 2008 16:28

tu avais raison concernant les boutons.bon j'ai fait la manip,on gagne un peu en assistance mais peu car elle est progressive.par contre il n'y a plus c'est petit à coup desagreables quand on restait proche de 25.
phil

yop1025
Messages : 195
Enregistré le : mar. 14 02 , 2006 19:43
Localisation : FR-65-Tarbes/TRIBAN TRAIL 28" + 408 / Batterie LITHIUM 36V13Ah 5200 KM au compteur
Contact :

Message par yop1025 » jeu. 20 03 , 2008 13:10


Répondre

Retourner vers « Matra MS »